The Mercedes Sprinter now has CRL ‘All-Glass’ Look Sprinter Van Windows to complement their great design. C.R. Laurence FW625R Mercedes Sprinter T-Vent Passenger Side Sliding Door Windows from Nomadic Supply Company are configured to fit within the OEM stampings and provide a customized OEM look. This great feature eliminates the time consuming efforts of laying out where the window will be installed. Just line it up to cut, starting on the upper inner dimple and follow along the OEM stamping!
The CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window has a large fixed pane on top, and two panels below. The rear bottom panel cranks out for ventilation, and is screened to prevent any insects from entering (the matching CRL FW621L driver side vented window has two bottom screened panels which both open).
The CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) fits the 144″ and 170″ Wheelbase and the Low and High roof Models from 2007 on. The CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) can also fit Dodge & Freightliner brands of Sprinter. The overall measurements of the CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) is 55 inches wide and 30-1/8 inches tall.
We recommend securing this window against break-ins with our:
Pikavo CRLSecure Mercedes Sprinter CRL Window Security Screen
CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window Specifications:
- Fits any 2007+ Mercedes-Benz Sprinter van passenger side sliding door
- Manufacturer Country: USA
- Manufacturer Warranty: 30 Days
- Glass Color = Solar Privacy Glass
- Glass UV Rating = 28%
- Window Measurement: 55″W x 30-1/8″H
- Opening Measurement: 22″W x 6-1/4″H
- Tilt Out Measurement: 9.5″
- Part Number: CRL FW625R
- Fits 2007+ Mercedes Sprinter 144″, 170″WB and 170″ extended models
- Has 28% dark gray factory tint
- Has one crank-out, opening bottom panel with detachable screen
- Has a clamp (trim) ring, so does not require adhesive, primer or sealant
- Uses tempered glass for maximum safety and strength
- Is tested to ANSI Z26.1 and FMVSS 205 safety standards
- Uses factory stampings for cut lines
- Is manufactured in the USA by C.R. Laurence.
CR Laurence has kept to its roots for the installation design of the CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side). Clamp Ring installation, developed in the 1970s, utilizes a factory urethane-bonded aluminum frame as the main structural frame of the window. The main frame of the CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) measures 48-1/4 inches wide and 25 inches tall. The mechanism and glass are integrated into the main structure.
To seal the CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side), an EPDM rubber seal is pre-applied to the aluminum frame. This seal, once the window is installed, will be compressed against the outer wall of the van creating a weather-tight seal.
The CRL FW625R Clamp Ring is attached to the main frame of the FW625R window from the interior side. When the hole is cut in the wall, the main frame of the window extends to the interior (about 1″) from the outside. The clamp ring caps over the main frame are attached by #8 x 3/4″ black pan-head screws. The basic idea is that the vehicles’ sheet metal wall is sandwiched between the rubber seal and aluminum frame on the outside and the clamp ring on the inside.
The CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) T-Vent opening features a rubber seal. When the vent is closed, the vent glass compresses on the seal to keep moisture and air out. Since the vent glass utilizes less pressure than the main seal, there can be slight water entry when using a high-pressure hose. (For example, when washing your van, we recommend simply utilizing a shower setting to avoid entry). Also, under extreme wind conditions, slight air noise can occur. The vent can generally open around 45 degrees to allow the air to flow in and the opening for the vent measures 22 inches wide and 5-3/4 inches tall.
The CRL FW625R Mercedes Sprinter T-Vent Sliding Door Window (Passenger Side) fiberglass mesh screen is attached to a powder-coated aluminum frame and easily clips into the vent opening, allowing for easy attachment and removal of the screen for cleaning and or maintenance of the window.
The CRL FW625R GearBox is fixed to the center cavity between the two bottom vent glasses. The gearbox is attached to the crossbar above the vent by a single rivet, and a Philips head bolt and nut combination secure the bottom of the gearbox. The gearbox has a metal spine to which a T-Handle is attached, and this is the handle you will turn to open and close the window.
The CRL FW625R torsion bar is a hollowed cylindrical bar that has a notch to slip into the gearbox on one end and slips into a fixed pivot bracket on the other. There are two welded arms that extend from the bar and have small wheels on the ends; these wheels incorporate into channel brackets that are attached to the vent glass. As the gear box is turned, the bar spins, and the arms extend outward or retract back into the window while the wheels glide up and down the channel to control the vent glass. In order to ensure the vent glass works smoothly and does not flop around, a heavy-duty spring is interconnected to the torque bar providing some pressure for a smooth, effortless function.
Camper Van Window Manufacturer Warranty and Manufacturer Defect Policy:
Camper Van Window Warranty and Defect Policy
Universal Clamp-Ring Camper Van Bunk Awning Window Documents:
Universal Clamp-Ring Camper Van Bunk Awning Window Installation Instructions
WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to